- Sku: 1338893
- Vendor: Banggood Dropship
Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli_S 48CH 200mW VTX 700TVL Camera
Short content about your product.
Short content about your product.
Icons are optional
USE RICH TEXT EDITOR
And big icons to highlight the product sale point
Old VTX | New VTX |
5.8G 40CH 0/25/200/600mw switchable VTX Output power & transmission distance: ≥0.5km@25mW, ≥1km@200mW, ≥2km@600mW
Transmitting power: 0mW/25mW/200mW/600mW
Full video format: NTSC /PAL
Input voltage & power dissipation: 7V~24V, 12V/260mA@600mW
Size: 20*30*9mm
Weight: ≤7g(except antenna)
With output power self-check function.
Nixie tube SCAN: frequency point (1-8), frequency band (A-E), power (1-3, 0=0mw, 1=25mw, 2=200mw, 3=600mw)
|
5.8G 48CH 200mW VTX ( LINK) |
Note:
1. This is the DIY version that comes unassembled.
2. Make sure the antenna is installed at the output end before powering up to avoid damaging internal components;
3. Note that the input voltage is within the specified range and is correct and correct to avoid damaging internal components;
4. If the antenna is replaced, select a standing wave and a gain antenna for a longer transmission distance;
5. Pay attention to classic protection during transportation and installation.
6. Take-off weight is about 450g.
Item | Specification |
210mm Frame Kit |
Wheel base: 210mm
Frame arm thickness: 5mm
Bottom plate thickness: 2mm
Side plate thickness: 2mm
Frame kit material: 3K carbon fiber & 6065 aluminium
|
2206 2150KV Brushless Motor |
Motor KV: 2150RPM/V
Idle current (Io/10V): 1.26A
Lipo cell: 3-5S
Weight: 31g
Max continuous current: 31A
Max continuous power: 496W
Max thrust: 1050g (4S/5")
Configu-ration: 12N/14P
Motor resistance (RM): 0.0572 Ω
Stator diameter: 22mm
Stator thickness: 6mm
Motor diameter: 27.7mm
Motor body length: 19.2mm
Overall shaft length: 34.2mm
Prop adapter shaft: M5
Bolt holes spacing: 16mm
Bolt thread: M3
Propeller: 5-6 inch
|
4 IN 1 30A BLHeli_S ESC |
Continuous current: 30A
Burst Current: 40A(10S)
Input voltage: 2-5S
BEC: 5V 2A BEC
Main control chip: 48Mhz EFM8BB2
Firmware: BLHeli_S supports Dshot600
MOS: 5*6 |
New F4 Flight Controller ( More Details, Click Here) |
Main control chip: STM32F405
Sensor: ICM20602
Power supply: 5V
Integrated OSD
Onboard LC filter
PID cycle rate & gyroscope refresh rate up to 32Khz
Supports BetaFlight / inav racing firmware
|
700TVL CMOS Camera |
Case size: 25mm*25mm
Weight: 9.5g
Total pixels: PAL: 1020H×596V (0.61MP); NTSC: 1020H×508V (0.52MP)
Effective pixels: PAL: 976H×582V (0.57MP); NTSC: 976H×494V (0.48MP)
Signal system: NTSC
Resolution ratio(horizontal center): 700TVL
Video output: 1.0Vp-p/75Ω
Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB
White balance: on/off optional
Exposure mode: electron exposure
Electronic shutter: 1/50(1/60) - 1/100000 S
Gamma correction: 0.45/1.0
Synchronization method: inter-sync
Camera lens: standard 2.8mm
Lens operating voltage: DC12V (wide voltage, measured can work normally at 7.5-13V)
Working current: 70mA (low power consumption)
Working temperature: -20℃~-60℃
Humidity: 0%~98%
|
Racerstar 5040 2 Blade Propeller |
Material: PC
Mounting hole: 5mm
Quantity: 2 CW & 2 CCW
Color: blue, red, yellow, purple, white (Delivery color randomly
|
Battery |
Not included Recommend 3-5S |
2 x 2206 2150KV brushless motor CW
2 x 2206 2150KV brushless motor CCW
1 x 4 IN 1 30A BLHeli_S ESC
1 x New F4 flight controller
1 x 700TVL CMOS camera
2 x Battery strap
2 x Racerstar 5038 2 blade propeller CW
2 x Racerstar 5038 2 blade propeller CCW
Add an additional description to your products. You may set the same content for all products.
Ex: Shipping and return policies, size guides, and other common questions.
Or you may link a dynamic source to show product fields like vendor or custom product meta fields.
Ex: Ingredients, nutritional info, additional features and other unique per-product data.
Have a question?
Eachine Tyro99 210mm DIY Version FPV Racing RC Drone F4 OSD 30A BLHeli_S 48CH 200mW VTX 700TVL Camera